Marine electronics & electrical services
Specialist work only: navigation and communications, networks, DC power, lithium, solar, battery-powered A/C, digital switching, wiring diagrams, and real diagnostics. Mobile service across Daytona Beach, Ponce Inlet, and New Smyrna Beach.
Marine electronics installation
New electronics are only as good as the installation behind them. Each install is planned around how you use the boat, with clean cable routing, proper connections, and setup done right the first time.
- Multifunction displays (MFDs)
- Radar
- GPS and heading sensors
- AIS
- VHF radios and antennas
- Autopilots
- Helm layout and integration with existing equipment
DC power & charging systems
Reliable electronics start with reliable power. DC distribution, protection, and charging are laid out so they are safe, easy to understand, and easy to service later: correctly sized conductors, protection at the source, clean bus bars, and every circuit labeled. There is no guesswork in the numbers: conductor sizes are calculated from the actual current, run length, and allowable voltage drop, then derated for bundling and engine-room temperature using the ABYC ampacity tables. Tyson is a Victron Energy factory-trained dealer and uses a Victron MK3-USB interface to configure and diagnose Victron inverter/chargers directly.
- DC distribution and panels
- Circuit protection and wire sizing
- Battery banks and battery switching
- Charging systems
- Inverters and inverter/chargers
- Victron configuration with MK3-USB
- Battery monitoring
Lithium & solar integration
Lithium batteries and solar can change how a boat runs, when they are integrated correctly. That means sizing the bank from the math, adding up the watt-hours and amp-hours every load uses in a real day aboard against what solar and charging can put back, matching every charging source to the battery system, and building in the protection, monitoring, and DC distribution a high-capacity bank needs. Not just swapping batteries. Done properly, lithium and solar can run loads that used to need a generator, including air conditioning on battery power. Victron systems are configured with factory training behind them.
- Lithium battery integration
- Bank sizing for real loads
- Charging source compatibility
- Battery management and monitoring
- Solar panels and charge controllers
- Inverter/charger configuration
- Lead-acid to lithium upgrades
Air conditioning on battery power.
Lithium and solar systems engineered for quiet nights at anchor and far less generator time.
Run your boat's air conditioning from lithium batteries and solar when you're away from the dock. At the dock, shore power already keeps things quiet. At anchor, a battery system means you no longer have to listen to the generator all evening just to stay cool.
Less generator time, on your schedule. On most larger yachts, a generator is still part of the system. Running every A/C load from batteries alone isn't realistic. What a battery system changes is when the generator runs. Run it during the day while you're out on the water or off the boat, alongside the solar, so the bank is full by afternoon. When you get back, shut it off. Solar keeps topping up late in the day, and the batteries carry the A/C through a quiet evening and night. With a properly designed system, there is still reserve left for a quiet morning.
Generator optional. On the right boat, the system can be designed to replace the generator entirely. That is a bigger build, sized from the boat's actual loads.
More nights away from the dock. If the only reason you're tied up is the air conditioning, you're paying for a slip by the foot, every night, all summer. A battery A/C system gives you the freedom to anchor somewhere quiet and still sleep cool. Every night you spend on the hook instead of in a slip is value back on what you put into the system, and it's why most people own a boat in the first place.
This is a properly engineered system, not a bigger battery. Each one is designed around your boat's A/C load and how you use it, with every part of the system sized and protected to work together.
- Lithium bank sizing
- Inverter selection and installation
- Charging from shore, engines, and generator
- Solar
- DC distribution
- Protection and monitoring
Now booking battery A/C projects for this season.
Troubleshooting & diagnostics
Real troubleshooting, not part swapping. Intermittent faults, dead networks, battery drain, equipment that just stopped working: the fix starts with understanding the system and finding the actual cause. You get a clear explanation of what was wrong and what was done.
- Electrical fault-finding
- Intermittent and hard-to-find problems
- Battery drain and charging issues
- Network and data faults
- Electronics that power up but do not work together
- Problems that have not been solved correctly yet
Digital switching & modernization
Digital switching cleans up the helm and gives better control and monitoring of onboard systems. Tyson is factory-trained and certified on both CZone and Maretron MPower. On older boats, modernization means turning years of add-ons and undocumented wiring into a system that is safe, clean, and serviceable.
- Digital switching systems
- CZone design and configuration
- Maretron MPower design and configuration
- Legacy wiring cleanup
- Replacing outdated electronics
- Helm and panel modernization
- Removing abandoned wiring and equipment
- Labeling and as-built documentation
Color wiring diagrams
Every major install can be delivered with a clean, full-color wiring diagram of the actual system as it was built on your boat, not a generic manual page. It is part of the Windward documentation package, so whoever works on the boat next can see exactly how it is wired.
- Full-color diagram of the installed system
- Wire colors, sizes, and circuit protection
- Device and network connections
- Matches the labels on the boat
- Part of the documentation package
- Print and digital copies
Diagnosed with the right tools, by someone factory-trained
Guessing is expensive. These are the tools and training behind the diagnosis.
- NMEA 2000
Actisense NMEA 2000 diagnostic tools
Reading raw network data to find the device or connection that is actually causing the problem.
- NMEA 2000
Second NMEA 2000 network tester
Verifying backbone power, termination, and the physical network, so the diagnosis happens at the data level instead of guessing.
- Victron Energy
Victron MK3-USB interface
Configuring and diagnosing Victron inverter/chargers directly, backed by Victron's 2-day hands-on factory training.
- Airmar
Airmar TDT1000 transducer tester
As an Airmar Certified Installer, qualifying transducers I install carry Airmar's extended three-year warranty starting the day of installation — and with my own TDT1000 tester, I can diagnose a transducer fault instead of guessing and replacing parts.
- Veratron
Veratron Diagnostic Tool
A USB interface to the NMEA 2000 and J1939 networks for the Veratron Configuration Tool: setting up, updating, and troubleshooting Veratron engine displays such as the VMH 70 directly instead of working around them.
Focused on electronics and electrical
Windward Marine Electronics does marine electronics and electrical work only. General boat repair and handyman jobs are not offered, so the work that is offered gets full attention.
Every job follows the same approach: understand the system, diagnose the actual fault, install cleanly, document the result, and communicate clearly. It comes from aviation, where a technician's signature certifies that an aircraft is safe to fly, and the paperwork proves no shortcuts were taken.
Need help with a new install, a system upgrade, or a problem that has not been solved correctly yet?
Request service online, give me a call, or send a text.